IBM SENG-3002-01 Uživatelský manuál

iSeries 270 and 82030xx MemoryCard InstallationVersion 5SENG-3002-01

__ 5. Do you have a new 2884 card assembly to install in your 820 system unit?Yes No↓ Go to step 7 on page 5.__ 6. Remove the empty card assembly C

__ 7. Remove the 2884 card assembly B or C from the system unit by doingthe following:__ a. Unlatch the two blue latches on the 2884 until the car

__ 2. Remove the blank filler cards from the next available positions by doing thefollowing:__ a. Push outward on the latches A that are located at

__ 6. Install the remaining memory cards.__ 7. When you finish installing all the memory cards, turn the card assemblyover, and slide it into the syst

Figure 6. Memory Connectors View 18 30xx Memory Card Installation V5R1

__ 2. Refer to the figure that matches your system unit to place the memory inthe correct order.__ 3. Place memory cards as follows on the processor:v

__ 8. Install the second memory card.__ 9. Do you have any other adapter cards or devices to install?No Yes↓If you have another device such as an adap

__ 4. DANGERAn electrical outlet that is not correctly wired could place hazardousvoltage on metal parts of the system or the products that attach to

__ a. Press the Mode Select button until the Manual modeindicator (a small hand) lights up.__ b. Press the Increment/Decrement push button until 02 ap

Note: If the status is not Operational, check the memory cards.__ g. If you have a printer, print the configuration list.Note: To print the hardware r

14 30xx Memory Card Installation V5R1

Unit CoversLocate the diagram of the unit you are working on. If you have a 270 system unitin a rack, go to “270 unit in a rack” on page 16.270 and 82

270 unit in a rack1. Press latches B and pull the server out using the handle C.2. Refer to previous unit diagram to remove the side cover.16 30xx

System unit control panelGo to the front of your system unit. Open the control panel door.Your control panel looks like either Figure 9 or Figure 10 o

If your control panel looks like this, before you can use F Increment/Decrementbuttons and G Enter push button, you need to press H Mode Selects

NoticesThis information was developed for products and services offered in the U.S.A.IBM may not offer the products, services, or features discussed i

TrademarksThe following terms are trademarks of the IBM Corporation in the United States orother countries or both:AS/400AS/400e seriesClient AccessCl

Readers’ Comments — We’d Like to Hear from YouiSeries 270 and 82030xx MemoryCard InstallationVersion 5Publication No. SENG-3002-01Overall, how satisfi

Readers’ Comments — We’d Like to Hear from YouSENG-3002-01SENG-3002-01Cut or FoldAlong LineCut or FoldAlong LineFold and Tape Please do not staple

iSeries 270 and 82030xx MemoryCard InstallationVersion 5SENG-3002-01

Printed in the United States of Americaon recycled paper containing 10%recovered post-consumer fiber.SENG-3002-01

NoteBefore using this information and the product it supports, be sure to read the “Safety andEnvironmental Notices” on page iii and the “Notices” on

Safety and Environmental NoticesDanger NoticesA danger notice calls attention to a situation that is potentially lethal or extremelyhazardous to peopl

Product Recycling and DisposalComponents of the system, such as structural parts and circuit cards, can berecycled where recycling facilities exist. I

Installation InstructionsBefore you begin__ 1. Take a minute to become familiar with these instructions. Note that you maynot complete every step in t

__ 9. If you encounter difficulties during the installation, contact your authorizeddealer or service provider.Powering off the system unit__ 1. Set t

__ 1. Do you have a 270 system unit?Yes No↓ You have a 820 system unit. Go to step 5 on page 4.__ 2. Does your system unit have an access cover as sho